Skip to main content

Avoid Drilling Accidents with Concrete Cutting Sydney

Concrete cutting Sydney is a regular practice in the construction industry. Cutting as a process is followed by possible hazards and accidents that a trained person will know how to avoid or minimize.
Drilling holes in the concrete walls is a complex process, which requires proper equipment and guidance from a professional. Most of the accidents at the construction site occur due to the use of unsuitable tools or machines handling by untrained persons.

Research the area before drilling

Before commencing the process of concrete drilling, first, research the area. In most cases, electrical equipment is installed behind the concrete walls. To avoid damaging the electricity network, the worker conducts a field inspection. If the location of the electricity network cannot be determined, the building's architectural plans will give the best picture. The worker must have this information to know where he may or may not drill.

Start drilling with shallow holes

If there is still a dilemma regarding electrical equipment behind the wall, it is best to start drilling with shallow holes. The worker will be sure he will not hit an electric wire and will be saved from potential disaster. Usually, the wires in the walls are installed at least 2, 5 centimetres deep, so keep this in mind before you start drilling.

Use specialised tools and machines for drilling

According to statistics, most accidents happen when drilling is taken out by amateur people, often alone in their homes. They use handheld drills that cause trembling or kickbacks, so injuries are inevitable. You need specialised tools and machines for accomplishing the task. If you do not have access to such equipment, call a core drilling Sydney that will complete the project for you.

Wearing a protective mask

Drilling holes in concrete walls produce dust in the air. Dust creates inhalation of silica dust, causing problems and diseases to human health. Although you plan to drill for a short period, you still have to wear a protective mask all the time.

Concrete core hole drilling is a process of creating holes of any diameter, usually for installing plumbing and electrical cables. Holes can have unlimited diameter and depth. Except for walls, drilling is performed on ceilings, roofs, bridges, tunnels, roads. They can be drilled at a specific angle, above and below ground or water. Drills are powered by electric, air, hydraulic and high-cycle electrical means.



To avoid possible hazards and accidents on the construction site, call a professional concrete cutting Sydney to complete the project for you.

Comments

Popular posts from this blog

Concrete Cutting Sydney – Dry vs. Wet

 There are many types of concrete cutting, but diamond cutting using a diamond saw blade is considered one of the most efficient techniques. This is because it offers less fracture to cutting surfaces and cleaner overall cuts. There are two primary techniques for diamond cutting: dry and wet.  Concrete cutting Sydney uses both of these methods depending on the project. Both techniques are very efficient and offer high-quality cuts, but they have certain differences. Read on to learn each technique's pros and cons to determine which is the right choice for your specific project. Dry Concrete Cutting Dry concrete cutting, as the name suggests, does not use water. This technique is typically handheld, and it is used intermittently. Following are the advantages of dry concrete cutting: •    No water source is needed on site. •    No electrical hazards from water coming into direct contact with equipment used for cutting concrete. •    I...

The Long-Term Benefits of Concrete Grinding Sydney

Concrete is one of the most versatile and durable building materials available, but over time, it can develop imperfections, wear down, or require refinishing for a variety of reasons. This is where concrete grinding in Sydney comes into play.  Whether you're looking to restore an old concrete surface, prepare it for new flooring, or give it a polished, decorative finish, concrete grinding can provide the solution.  Key Purposes of Concrete Grinding Surface Preparation One of the most common uses of concrete grinding is surface preparation. Before installing new flooring, coatings, or tiles, it's essential to have a clean and smooth surface. Concrete grinding is an effective way to remove old flooring materials, adhesives, paint, and other residues that can interfere with new installations. Grinding helps to create a level, clean surface that ensures a strong bond between the new flooring and the underlying concrete. Without proper surface preparation, new flooring materials m...

Visiting Pawn Broker Bankstown for Pre-Holiday Shopping

Interest for pawn broker Bankstown is particularly increasing as the Christmas and New year's euphoria approaches. Two equally important reasons contribute to this fact. Festive mood leads to festive shopping. Every individual wants to buy a unique gift for the closest and most loved ones, regardless of whether they are buying for their children, spouse, parents, friends or colleagues. December is special because it is time to buy some holiday gifts. Nowadays, people feel comfortable buying items from pawn shops. So the period before the holidays is quite popular with both, brokers and customers. This month, pawn shops offer special sales and additional discounts for the customers. Before the holiday euphoria, people increase their attendance in these shops, mainly because of two factors. First, people are becoming more aware that they can buy electronic appliances, antiques and a variety of jewellery at a much lower price, rather than buying new ones in expensive stores. Secon...